Lifestyle

Pink Channel Tufted Banquette DIY


Have you ever wanted something for your home that felt a little crazy, because you really wanted it, so you just made it happen? That’s basically how I feel about my pink velvet banquette in our newly renovated kitchen.

I know I want some kind of breakfast nook because we have a corner of our kitchen that doesn’t make sense like cabinets or excess countertop space.

When the idea for a party came to me, I knew I wanted to do it with the same sentiments as the lovable (and Pinterest-worthy) person. Sketch Restaurant in London. The velvet pink is a must have, and I thought I’d add some channel tweaks to make it feel a little more special.

Thankfully, I’m familiar with Mandi’s Channel Tufted Storage Banquette from a few years ago, and I think that would be a great start to the project.

Placing the booth in an L-shaped corner with the ends open (instead of partially covering a straight wall from end to end like Mandi did) poses its own set of challenges.

But after enough trial and error — and I’ve found them all — you can take or skip any steps you need based on the shape and area you’re adding a banquette to.

Pink party table in the kitchen corner

Munition:
-hemp upholstery fabric (I used 6-7 yards This fabric is pink Bowie)
Polish go between your velvet and foam
-6 inch pine board to support each half washer
half washer (I used 6 inch wide spacers and you can email them to ask them to cut them in half for you)
metal strap (I used 8 with 4 on each part)
cushion cover (there are different thicknesses but I used 3″)
– plywood for chair legs
-Cutter (optional depending on the shape of cushion you need)
saw machine or circular saw for cutting straight cuts on 3/4 plywood or plank seat bases
butcher if you have a corner banquette to cut your 3/4 table at a 45° . angle
– staple gun (recommended electricity)
construction adhesive (optional)
-L-shaped corner brace (I used some these 1 1/2 splint packs)
-3″ or 4″ cutting board for cutting your banquette (optional)

banquette with hardcover template of seating on top

Making a pedestal: First, I needed to take a large sheet of plywood and cut it in the shape of the L-shaped seating area. We installed the base cabinets when we fitted the rest of the kitchen cabinets, so I installed the base cabinets. only build on those cabinets (Mandi .’s banquette post show you how to build the bottom if you want to build your own).

I wanted the seat to hang over the front and side edges of the seat about 1″, so I made sure the overhang was there as well. Then I cut the shape with a jigsaw.

You can also use a large piece of cardboard to make the cardboard pattern first (like I did for the trace on the wood) if you want, but make sure it fits well before cutting the wood. Highly recommended!

After the wood was cut, I placed the two pieces of foam sitting next to each other to form an L shape and marked where they needed to be trimmed with a marker to fit the shape of the chair.

To cut the foam, an electric bread knife or a standard bread knife is best for cutting through the green foam wrap.

banquette with the beginning of the channel support section

Seat cover: Once the chair is in shape, it’s time to upholster it with velvet. If you have a straight bench with no corners to turn, you can essentially turn your chair upside down and place the front foam on the underside of the velvet fabric with some dents in between the layers of velvet and foam.

Your fabric will be face down on the floor with the flat side above, and then the face down chair will rest on that side.

For the no-sew option, you can simply pull and wrap the fabric over and over the edges of the chair and pin it in place on the plywood every few inches to keep it in place. Then wrap the corners as a gift (you can see how Kara did it in Velvet couch with DIY color block tutorial).

You can see that my L-shaped cushion has a seam where the two sides meet at a 45° angle, so I had to staple and sew the fabric together that way. Firstly and then wrap and pin it to the undercarriage.

The meeting point where it cascades down the front of the cushion can be a tricky one, but you can fold and pin the excess underneath to make it as smooth as possible, or you can try and pin the excess at backside.

Then sew a seam down the front like I did so you can trim most of the excess so it looks a little smoother. It’s certainly not perfect (I wish I was a master tailor in times like these!), but it works well enough to get the job done.

box corner on fabric cushion

I wanted the contact corner to look more finished on mine, so I did the wrap and pin method I mentioned above on all the hidden corners. I pinned and sew a corner of the box on an exposed corner to give it a sleeker look before folding the excess fabric underneath for pinning.

*Note: Remember, if you’re using velvet, pay attention to which direction the bead goes when you attach it so it all flows in the same direction when it’s attached!

Cutting wood/foam sections: Once the bottom of the bench is done, it’s time to move on to the quilting channel section! I took 3/4 inch thick boards the same size as my semi-circular pads and cut them to the lengths of my upper left and right sides (3 for each side).

Since I have a corner to deal with, I also doubled the board at a 45° angle on the edges where they would meet in the center.

Then I put the semi-circular spacers on top of the board (you can use some tape to keep them on the board temporarily) and cut them down to fit the board. I cut the outside straight edge first (or just line it up with an existing end of a spacer).

Then for the edge with the 45° angle in the middle, I would cut it straight, hold it in its place on the wall, and then use the knife to cut the eyeball at a 45° angle as you see above.

fabric, polish, foam and board for lining

End of sections: Once the foam has been cut for the channel quilting pieces, I place the velvet strips that I have pre-cut on the floor.

The bands are long and wide enough to cover the front and can be wrapped around the back to pin face down. Then I add a layer of polish, and my board with foam (foam side down).

For the gloved edges that meet at the center corner, I folded the fabric several times and pinned it underneath.

I did the same for the outside edges that won’t be visible (the right side of the banquette runs into our cabinet), but you can do this wrapping method for any visible edges if you don’t mind the looks.

As for my edges to be visible, I decided to sew them instead of folding and pinning like above for a cleaner look. I made a half circle slightly larger than the half circle of the foam pad and pinned and sewed the piece to the edge of my fabric (sides should be together when pinning and sewing).

I left excess fabric below the half circle when I cut the pattern so I had plenty of fabric to fold and pin.

sew a half circle of fabric edge

After it was sewn and right side out, it looked like the above and I was able to tuck it into the end of the foam sheet. Then I folded/pinned the excess fabric underneath for a cleaner look.

You can do either method depending on your sewing skills, but if your ends are hidden I would definitely go for the quicker folding/pinning method rather than sewing.

three semi-circular spacers with metal straps attached

Attach the following sections together: Once my three sections were covered in velvet, I used my metal lanyard to attach the sections together for each group of three.

I left the lanyard hanging at the bottom so I could screw the part into the wall to keep the bottom in place.

painter's tape and wall brackets

Prepare the wall: Then I used painter’s tape to mark where I wanted to touch the top of the banquette (I’m trying to make it with the marble window ledge on the right side of the banquette). .

I put some L-shaped brackets there to hold the top of the banquette in place and gave me something to attach my final wood trim to.

half of banquette favors attached

Attach the back sections to the wall: It would be easiest to screw in the back and then slide into your seat cushion, but I had to put the seat back in front of the back right. My kitchen counter was properly angled back after the back was turned on.

Add wood trim (optional): You can see that my back is in and the top L brackets are holding the top in place, but the walls in our old house weren’t exactly straight, so there was a gap. where the wall curves inward a bit in that area .

Besides rebuilding the entire wall properly, my best option would be to cover the gap with some wooden trim that goes up the side of the table and follows the curve of the wall (and paints it). the same color as the wall) to help mask the problem.

I placed a 4-inch board on top of my dining table and used a compass fixed to the size of the widest part of the space to trace along the wall. Then I scribbled on the wood where I should cut it with my hacksaw for a snug fit.

This is a great video that shows you how to do it correctly with just a pencil or a small block of wood.

After I had scribbled the board above, I was able to use my ruler saw to cut other pieces to fit the other gaps I wanted to cover, glue them together with wood glue, paint them white, and then fit them in. it’s on the banquette mounts. .

You can screw/nail it to the wooden backing of banquette sections or even glue it to metal supports.

Note: If you don’t need to cover any gaps in the wall like I did, you can simply use construction glue to attach these panels to the wall or refer Mandi .’s banquette post if you are going from one side of the wall to the other there are best practices there.

Pink party table in the kitchen corner
Pink party table in the kitchen corner
Pink party table in the kitchen corner
Pink party table in the kitchen corner

I would say this was a marathon of a project for me and a lot of issues to deal with with our particular space and corner composition, the windowsill on one side, the side of the table top and the other elements. uneven wall.

The whole thing has been dragged around for almost a year among other projects in the area/kitchen, but I can’t tell you how relieved it was to get it done and it turned out so beautiful it was real. worth. went into it.

Just this morning, my daughter was sitting at the party table and coloring on her pjs, and it just brings a little joy to my morning seeing her there (and I love it with that star rug right in front of it).

Hope this inspires you to make your own band or make a DIY project that will brighten up your home! so so. Laura

Love a good makeover kitchen? Check out these posts…
How I Refresh My Kitchen Cabinets In Just One Afternoon
Holiday House kitchen before and after
Laura’s Kitchen Tour (Part 2!)
Elsie’s Kitchen Tour (Before and After)



Source link

newsofmax

News of max: Update the world's latest breaking news online of the day, breaking news, politics, society today, international mainstream news .Updated news 24/7: Entertainment, Sports...at the World everyday world. Hot news, images, video clips that are updated quickly and reliably

Related Articles

Back to top button
Immediate Matrix Immediate Maximum